What the video covers: mixing to injection
Soulera Wellness runs through the entire process in one pass, from a sealed vial to a completed injection, which makes it a useful refresher once you already know the basics. It breaks down into two parts: getting the mix right, then getting the injection right.
- 1
Reconstitute with bacteriostatic water. Draw it slowly, add it down the inside wall of the vial rather than onto the powder, and swirl gently until the solution runs clear. No shaking, at any point.
- 2
Draw the dose and clear air bubbles. Insert the needle through the center of the stopper, draw back to the calculated unit mark, then hold the syringe needle-up and flick it so bubbles rise to the top before pushing them out.
- 3
Pinch the skin and inject at 45 to 90 degrees. Pinch an inch or two of tissue, insert in one smooth motion, release the pinch, and depress the plunger slowly over 5 to 10 seconds rather than all at once.
- 4
Withdraw and don't rub the site. Pull the needle out at the same angle it went in, press a clean alcohol swab on the site for about 10 seconds, and drop the needle straight into a sharps container.
What reconstitution means
Most research peptides ship as a dry, freeze-dried powder. Reconstitution means adding a measured amount of bacteriostatic water so the powder dissolves into a liquid you can draw with an insulin syringe. Done carefully, it takes about two minutes, and getting the water amount right is what makes your dose math work.
What you need
- The peptide vial, at room temperature so the powder dissolves easily.
- Bacteriostatic water, sterile water with 0.9% benzyl alcohol as a preservative.
- A mixing syringe (a 1 to 3 ml syringe works well) and U-100 insulin syringes for dosing.
- Alcohol swabs for both vial stoppers and the injection site.
- A sharps container for used needles.
How much bacteriostatic water to add
The water amount sets the concentration, not the dose. More water spreads the same peptide across more liquid, so each dose takes more units on the syringe, which is easier to measure for small doses. On a U-100 insulin syringe, 100 units equals 1 ml.
| Vial size | Water added | Concentration | Each 10 units holds |
|---|---|---|---|
| 2 mg | 1 ml | 2,000 mcg/ml | 200 mcg |
| 5 mg | 1 ml | 5,000 mcg/ml | 500 mcg |
| 5 mg | 2 ml | 2,500 mcg/ml | 250 mcg |
| 10 mg | 2 ml | 5,000 mcg/ml | 500 mcg |
| 10 mg | 3 ml | about 3,333 mcg/ml | about 333 mcg |
To get the exact units for your vial and dose, use the peptide dosage calculator. Doses themselves are not covered here; most come from community practice rather than human trials, and the peptide dosing guide explains where each range comes from.
Step by step: mixing the vial
- 1
Wash your hands and wipe both stoppers. Use a fresh alcohol swab on the peptide vial and the water vial, and let them air dry.
- 2
Draw the water. Pull the planned amount of bacteriostatic water into the mixing syringe.
- 3
Add it slowly down the side. Angle the needle so the water runs down the inside wall of the peptide vial instead of spraying onto the powder.
- 4
Swirl, never shake. Roll the vial gently between your fingers until the liquid is completely clear. Some peptides take a few minutes.
- 5
Label and refrigerate. Write the date and the concentration on the vial, then store it in the refrigerator.
How to store a reconstituted vial
A reconstituted multi-dose vial mixed with bacteriostatic water is generally good for up to 28 days refrigerated. Keep it cold and away from light, do not freeze it, and replace it once the 28 days are up or if the liquid turns cloudy or shows particles.
Common mistakes
- Shaking the vial instead of swirling it.
- Using sterile water for a vial you plan to use for weeks. It has no preservative.
- Forgetting the concentration. Without it, the units on your syringe mean nothing. Write it on the vial.
- Reusing needles or skipping the alcohol swab on the stopper.
- Keeping a vial past 28 days. Mix a fresh one instead.
Frequently asked questions
How much bacteriostatic water do I add to a peptide vial?
Most people add 1 to 3 ml. The amount of water does not change how much peptide is in the vial, only how much liquid each dose takes up. More water means more units per dose, which is easier to measure for small doses. A 5 mg vial with 2 ml of water gives 2,500 mcg per ml, so a 250 mcg dose is 10 units on a U-100 insulin syringe.
Can I use sterile water instead of bacteriostatic water?
Sterile water has no preservative, so a vial mixed with it is generally treated as single use. Bacteriostatic water contains 0.9% benzyl alcohol, which slows bacterial growth and is why it is the standard choice for a vial you draw from over several weeks.
How long does a reconstituted peptide last?
A reconstituted multi-dose vial mixed with bacteriostatic water is generally good for up to 28 days in the refrigerator. Keep it cold and out of light, do not freeze it, and write the mixing date on the vial so you know when to replace it.
Should I shake a peptide vial after adding water?
No. Shaking can damage fragile peptide chains. Let the water run down the inside wall of the vial, then swirl or roll it gently until the powder dissolves and the liquid is clear. If it stays cloudy or has particles, do not use it.
For the full guide with dosing calculations and site rotation, see BioStackIQ's Peptide Injection Guide.
Wondering which needle to use? Read what needle size to use to reconstitute peptides without damaging the vial stopper, or browse more community questions.
Related: peptide mixing video, injection site rotation, and where to buy BPC-157 (vials ship as powder that needs reconstituting).